100-105 Dumps 100-105 Exam Questions 100-105 PDF Dumps 100-105 VCE Dumps Cisco Exam

[New-100-105-Dumps]Instant Download Braindump2go 100-105 PDF Dumps and 100-105 VCE Dumps 295q[21-30]

January 30, 2017

2017 New CISCO 100-105 Exam Dumps (PDF & VCE) with New 100-105 Questions Updated!

1.|NEW 100-105 Exam Dumps (PDF & VCE) 295Q&As Download:
http://www.braindump2go.com/100-105.html
2.|NEW 100-105 Exam Questions & Answers:]
https://1drv.ms/f/s!AvI7wzKf6QBjgjFYeld4mJ-E9p1q

QUESTION 21
Refer to the exhibit. The MAC address table is shown in its entirety. The Ethernet frame that is shown arrives at the switch. What two operations will the switch perform when it receives this frame? (Choose two.)

A.    The switch will not forward a frame with this destination MAC address.
B.    The MAC address of 0000.00aa.aaaa will be added to the MAC Address Table.
C.    The MAC address of ffff.ffff.ffff will be added to the MAC address table.
D.    The frame will be forwarded out all active switch ports except for port fa0/0.
E.    The frame will be forwarded out fa0/0 and fa0/1 only.
F.    The frame will be forwarded out all the ports on the switch.

Answer: BD
Explanation:
If the switch already has the MAC address in its table for the destination, it will forward the frame directly to the destination port. If it was not already in its MAC table, then they frame would have been flooded out all ports except for the port that it came from.

QUESTION 22
On a Cisco switch, which protocol determines if an attached VoIP phone is from Cisco or from another vendor?

A.    RTP
B.    TCP
C.    CDP
D.    UDP

Answer: C
Explanation:
The Cisco Unified IP Phone uses CDP to communicate information such as auxiliary VLAN ID, per port power management details, and Quality of Service (QoS) configuration information with the Cisco Catalyst switch.

QUESTION 23
Refer to the exhibit. What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A?
A.    VLAN 1 on RT-A
B.    IP routing on SW-A
C.    default gateway on SW-A
D.    crossover cable connecting SW-A and RT-A

Answer: C
Explanation:
In order for the switch to reach networks that are not local, such as networks attached to different interfaces of the router, it will need to set its default gateway to be the IP address of the attached router.

QUESTION 24
A switch receives a frame on one of its ports. There is no entry in the MAC address table for the destination MAC address. What will the switch do with the frame?

A.    drop the frame
B.    forward it out of all ports except the one that received it
C.    forward it out of all ports
D.    store it until it learns the correct port

Answer: B
Explanation:
Understanding this concept is prime for understanding that when switch receives the data frame from the host not having the MAC address already in the MAC table, it will add the MAC address to the source port on the MAC address table and sends the data frame. If the switch already has the MAC address in it’s table for the destination, it will forward the frame directly to the destination port. If it was not already in it’s MAC table, then they frame would have been flooded out all ports except for the port that it came from.

QUESTION 25
At which layer of the OSI model does the protocol that provides the information that is displayed by the show cdp neighbors command operate?

A.    application
B.    transport
C.    network
D.    physical
E.    data link

Answer: E
Explanation:
CDP is a device discovery protocol that runs over Layer 2 (the data link layer) on all Cisco- manufactured devices (routers, bridges, access servers, and switches) and allows network management applications to discover Cisco devices that are neighbors of already known devices. With CDP, network management applications can learn the device type and the Simple Network Management Protocol (SNMP) agent address of neighboring devices running lower-layer, transparent protocols.

QUESTION 26
Which two characteristics apply to Layer 2 switches? (Choose two.)

A.    increases the number of collision domains
B.    decreases the number of collision domains
C.    implements VLAN
D.    decreases the number of broadcast domains
E.    uses the IP address to make decisions for forwarding data packets

Answer: AC
Explanation:
Layer 2 switches offer a number of benefits to hubs, such as the use of VLANs and each switch port is in its own separate collision domain, thus eliminating collisions on the segment.

QUESTION 27
Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface? (Choose two.)

A.    router#show version
B.    router#show ip interface
C.    router#show protocols
D.    router#show controllers
E.    router#show running-config

Answer: BC

QUESTION 28
Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.)

A.    layer 3 support
B.    port security
C.    redundant components
D.    VLANs
E.    PoE

Answer: BD
Explanation:
The primary function of an access-layer is to provide network access to the end user.
The hardware and software attributes of the access layer that support high availability include security services for additional security against unauthorized access to the network through the use of tools such as 802.1x, port security, DHCP snooping, Dynamic ARP Inspection, and IP Source Guard.

QUESTION 29
Refer to the topology and switching table shown in the graphic. Host B sends a frame to Host C. What will the switch do with the frame?

A.    drop the frame
B.    send the frame out all ports except port 0/2
C.    return the frame to Host B
D.    send an ARP request for Host C
E.    send an ICMP Host Unreachable message to Host B
F.    record the destination MAC address in the switching table and send the frame directly to Host C

Answer: B
Explanation:

QUESTION 30
What is the purpose of assigning an IP address to a switch?

A.    provides local hosts with a default gateway address
B.    allows remote management of the switch
C.    allows the switch to respond to ARP requests between two hosts
D.    ensures that hosts on the same LAN can communicate with each other

Answer: B
Explanation:
Switch is a layer 2 device and doesn’t use network layer for packet forwarding. The IP address may be used only for administrative purposes such as Telnet access or for network management purposes.


!!!RECOMMEND!!!

1.Braindump2go|NEW 100-105 Exam Dumps (PDF & VCE) 295Q&As Download:
http://www.braindump2go.com/100-105.html

2.Braindump2go|NEW 100-105 Study Guide:
https://youtu.be/H1Mo6SKblEw